HST3D Overview
HST3D Detailed Description
HST3D Join Contours/Declutter Contours
HST3D Prices

Both the Join Contours and Declutter methods first clear the layer before writing to it. If there is an error when writing the data to the layer, this will result in a loss of data. An error might occur in the Declutter PIE if "Allow Intersection" is turned off and some of the contours cross each other after some vertices are removed. Thus it is a good idea to save your file before running either of these PIEs.

After "Declutter Contours" applied

Before "Declutter Contours" applied

declutterbefore2
declutteraft2

A word of warning about the "Declutter Contours" method. After removing vertices, some contours that previously did not overlap may overlap and the geometric relationships among contours may differ. For example, in the illustrations below, the -200 ft contour has been reduced to a single point that is no longer inside the -150 ft contour as it was before.

After "Declutter Contours" applied

dclutaft

Before "Declutter Contours" applied

dclutbef

When you click OK, the contours on the layer will be processed so that vertices that are closer together than the desired spacing will be eliminated if the "Delete nodes based on spacing" check box is checked. However, if the "Delete Node based on angle" check box is checked, nodes will only be deleted if the angle at the node exceeds the limit you specify. The effects of "Declutter Contours" is illustrated below. The first diagram shows contours with very closely spaced vertices. In the second illustration, many of the vertices have been eliminated.

declutterdialog

If two contours have starting or ending points that are even slightly different, the contours will not be combined. To ensure that such contours are combined, make sure the "Special/Allow Intersection" is checked. Then move the end of one of the contours close to the end of the other. The cursor will change to a hollow cross to indicate that it has detected another vertex. When you release the mouse, the vertex will be placed exactly over the position of the other vertex.

Reducing the number of vertices in a layer can make the export process faster. If the vertices are much more closely spaced than the grid spacing, reducing the number of vertices may have little effect on the model inputs. To reduce the number of vertices in the contours in a layer, first turn "Allow Intersection" on for that layer. Then select "Declutter Contours" from the "File/Import" menu. A dialog box will appear with a list of information layers. Select the information layer in which you wish to reduce the number of vertices. Another dialog box will appear in which you should enter the desired vertex spacing.

After "Join Contours" applied

joincontoursaf1

Before "Join Contours" applied

joincontoursbef1

HST3D Model - simulation of heat and solute transport in three-dimensional ground-water flow systems

HST3D Model Categories: flow models - pathlines/capture zones, flow models - saturated zone, heat transport, solute transport models - saturated zone, saltwater intrusion models
 

Join Contours and Declutter
Contours PIEs

The JoinContoursPie.dll provides a method for combining multiple contours into a single contour and reducing the number of vertices in contours.

You may sometimes wish to join contours together to make it easier to manipulate them. To join contours together, select "Join Contours" from the "File/Import" menu on any information layer. A dialog box will appear listing the information layers. Select the layer in which you want to combine contours. The PIE will read the contours from the layer. If any two contours have exactly the same starting or ending point and all their parameter values are the same, those contours will be combined into a single contour. Below is an illustration of the effect of the Join Contours method. The first illustration shows the situation before joining contours. There are numerous short contours with parameter values of -70 and -80. In the second illustration, those numerous contours have been combined into a much smaller number of contours.

This product is no longer commercially available. However, it can be downloaded for free on our download site.

HST3D

Please reference the link below for updated products with simular functionality.

Similar Products Catagories:

Scientific Software Group    P.O. Box 708188   Sandy, Utah 84070
Phone (801) 208-3011   Toll Free (U.S.) 1-866-620-9214    Fax (801) 302-1160    E-mail
info@scisoftware.com
Copyright 1998   Scientific Software Group    All rights reserved